欢迎访问欢迎访问天桥区欣飞板业经销处!
阳光板、耐力板、FRP(波浪瓦)、灯箱片
我们只生产质量保障的阳光板等产品

统一服务热线:

15806664558

首页>新闻中心>怎么固定耐力板大家知道吗
产品分类 PRODUCTS
联系我们

天桥区欣飞板业经销处

联系人:焦经理 

电话:15806664558 

手机:15806664558
          15066129603
          13969012996
地址:济南市历城区历山北路佳园装饰材料南区A7-30号


怎么固定耐力板大家知道吗

来源:http://www.wanzhongyue.com/ 日期:2020-05-14 发布人:admin 浏览次数:

  为了安全顺利的使用济南耐力板,在安装的时候,它会被牢固的固定住,这样使用的时候会更放心,放心,那么你知道耐力板怎么固定吗?你对此了解多少?不清楚吗?没关系,下面我们济南阳光板公司将为您介绍,希望能对您有所帮助。
  In order to use Jinan endurance board safely and smoothly, when it is installed, it will be firmly fixed, so that when it is used, it will be more reassuring and reassuring, so do you know how to fix the endurance board? How much do you know about this? Don't you know? It's ok. Now we will introduce Jinan Yangguang board company to you, hoping to help you.
  一、耐力板安装固定施工
  1、 Installation and fixation of endurance board(1)耐力板固定方法
  (1) Fixation method of endurance board
济南阳光板
  切割耐力板时,切割过程中会产生粉尘。这时,一般都是在旁边的锯子放入水中,把锯子锯开,一直往下跑,这样在锯开的时候,产生的灰尘就不会飞得到处都是,也便于以后清理。当下一次锯切耐力板时,它必须缓慢下降,还需要保持一个平衡的力量来切割,当它要下降时,它的切割速度一定要快。而此锯相对较平,也不会产生板材切角现象。
  When cutting the endurance board, dust will be generated during the cutting process. At this time, the saws beside are usually put into the water, and the saws are sawed and run all the way down, so that when the saws are cut, the dust generated will not fly everywhere, and it is also convenient for later cleaning. The next time you saw the endurance board, it had to slow down and maintain a balanced force to cut. When it was going down, it had to cut faster. And the saw is relatively flat, and it will not produce the phenomenon of cutting angle of the plate.
  同时,在切割时还需要注意将钢板夹紧,也可以将耐力板固定死。防止振动在切削过程中,造成切削不均匀,而不能使用。还可以防止耐力板的表面和台面会出现摩擦,进而出现非常粗糙的加工表面。
  At the same time, the steel plate should be clamped when cutting, and the endurance plate can also be fixed. Prevent vibration in the cutting process, resulting in uneven cutting, and can not be used. It can also prevent the friction between the surface of the endurance board and the table, and then the very rough machining surface.
  耐力板不需要热弯,因为两边都要有骨架固定!你只要把盘子弯曲成你想要的厚度,然后把它固定在合适的位置!如果你想让它再次变成某种形状,它可能必须是热成型的。只要曲率不超过90度!
  The endurance board doesn't need to be hot bent, because there should be a skeleton on both sides! You just bend the plate to the thickness you want, and then fix it in the right position! If you want it to be a shape again, it may have to be hot formed. As long as the curvature does not exceed 90 degrees!
  二、济南耐力板固定安装方法
  2、 Fixed installation method of Jinan endurance board(1) PC板嵌入时,应留有适当的嵌入和扩展空间。如果嵌入的量太少,PC板可能由于风压或其他压力而脱落;如果膨胀空间不够,PC板还可能由于膨胀而受力,造成损坏。
  (1) When the PC board is embedded, appropriate space for embedding and expansion shall be reserved. If the embedded amount is too small, the PC board may fall off due to wind pressure or other pressures; if the expansion space is not enough, the PC board may also be stressed due to expansion, causing damage.
  (2) PC板上的保护膜会影响与密封件的附着力,所以在预埋PC板前应预埋部分保护膜除去。5 - 10毫米。
  (2) The protective film on the PC board will affect the adhesion with the seal, so some protective films should be removed before embedding the PC board. 5 - 10 mm.
  螺丝安装
  Screw installation
  (1)螺杆间距,根据钢板的厚度,作适当的配置,间距过小和过大都不好。若间距过小,有时会因过紧而造成应力过大,造成损坏;如果间距过大,可能会使PC板固定不稳定。这个建议使用以下间距:
  (1) Screw spacing, according to the thickness of the steel plate, make appropriate configuration, too small and too much spacing is not good. If the spacing is too small, sometimes the stress will be too large due to over tightening, resulting in damage; if the spacing is too large, it may cause unstable fixation of PC board. The following spacing is recommended for this:
  a、板材厚度3.0mm以下,间距10 ~ 20cm
  a. Plate thickness is less than 3.0mm, spacing is 10 ~ 20cmb、板厚3.0mm以上,间距20-30cm
  b. The thickness of the plate is more than 3.0mm, and the spacing is 20-30cm如果分层固定,间距为20-30cm
  If fixed in layers, the spacing is 20-30cm注:如果PC板直接用自攻螺钉固定,螺钉间距越大,板材受应力损伤的可能性越小。
  Note: if the PC board is directly fixed with self tapping screws, the larger the screw spacing is, the less likely the board is to be damaged by stress.
  (2)当螺孔的位置太靠近PC板边缘时,很容易造成板破损。一般来说,螺孔的位置至少是PC板边缘螺孔直径的2.5倍。例如,对于直径为4mm的螺钉,螺钉孔的位置应至少距离PC板边缘1cm。
  (2) When the screw hole is too close to the edge of PC board, it is easy to damage the board. Generally speaking, the position of screw hole is at least 2.5 times the diameter of screw hole on the edge of PC board. For example, for screws with a diameter of 4 mm, the screw holes should be located at least 1 cm from the edge of the PC board.
  (3)螺孔的大小应考虑PC板夏、冬段和昼夜热胀冷缩的差异。一般来说,螺钉的孔径应比螺钉直径大2 ~ 4mm,以预留膨胀空间。
  (3) The size of screw hole should consider the difference of thermal expansion and cold contraction of PC board in summer, winter and day and night. Generally speaking, the hole diameter of the screw should be 2 ~ 4mm larger than the screw diameter to reserve expansion space.
  (4)不要把螺丝锁得太紧,否则会变形造成应力。
  (4) Do not lock the screw too tightly, otherwise it will deform and cause stress.
  (5)为了降低螺丝对板材的直接压力,可以用垫片填充其间,但PVC垫片和一些橡胶垫片会损坏PC板,不能使用。建议垫片材质为三元乙丙橡胶、硅胶、氯丁橡胶。
  (5) In order to reduce the direct pressure of the screw on the board, the gasket can be used to fill the gap, but PVC gasket and some rubber gasket will damage the PC board and cannot be used. It is suggested that the gasket materials are EPDM, silica gel and neoprene.
  (6)锁紧在PC板上的螺丝不应该是自攻螺丝,否则会产生应力,应力会随着板的厚度增加而增加。
  (6) The screws locked on the PC board should not be self tapping screws, otherwise there will be stress, which will increase with the thickness of the board.
  以上是济南阳光板公司小编为大家介绍的相关内容,想要了解更多内容,欢迎访问网站:http://www.wanzhongyue.comThe above is the relevant content introduced by Jinan sunshine board company. To learn more, please visit the website: http://www.wanzhongyu.com
相关新闻


  天桥区欣飞板业经销处            联系人:焦经理            座机:15806664558
 手机:15806664558        15066129603       13969012996
  技术支持: 济南诺商   鲁ICP备14016125号 网站地图 XML TXT

统一服务热线

15806664558 

鲁公网安备 37010502001033号

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】