欢迎访问欢迎访问天桥区欣飞板业经销处!
阳光板、耐力板、FRP(波浪瓦)、灯箱片
我们只生产质量保障的阳光板等产品

统一服务热线:

15806664558

首页>新闻中心>阳光板的装置要留意事项,你知道多少
产品分类 PRODUCTS
联系我们

天桥区欣飞板业经销处

联系人:焦经理 

电话:15806664558 

手机:15806664558
          15066129603
          13969012996
地址:济南市历城区历山北路佳园装饰材料南区A7-30号


阳光板的装置要留意事项,你知道多少

来源:http://www.wanzhongyue.com/ 日期:2018-08-31 发布人:admin 浏览次数:

要留意为阳光板的热胀冷缩留出空地。阳光板的线性胀大系数是6.75*10^(-5)m/(m*k),即温度每升高1摄氏度,1m*1m的板沿长度和宽度方向各胀大0。075mm。相应的,温度每下降1摄氏度,板材亦缩短相同的量。用户须依据工程所在地的四季温差,算出预留的装置空地。板材外表较大的温度差约为80摄氏度,则1m*1m的板材装置预留空隙为:0.0675*80=5.4mm,果板材过长,还需要扩孔。
Be careful to leave room for the expansion and contraction of the sunlight board. The linear expansion coefficient of the solar panel is 6.75 * 10 ^ (- 5) M / (m * k), that is, for each temperature increase of 1 degree Celsius, the plate of 1 m * 1 m expands 0 along the length and width directions. 075mm. Correspondingly, the temperature is reduced by 1 degrees Celsius. The user should calculate the reserved space on the basis of the four seasons temperature difference in the location of the project. The maximum temperature difference of the plate surface is about 80 degrees Celsius, then the gap reserved for the plate device of 1m * 1m is: 0.0675 * 80 = 5.4mm, the fruit plate is too long, and the hole needs to be reamed.
阳光板传统装置办法分为:
The traditional installation of sunlight board is divided into:
1干式装配法:此办法需在铝型材中穿入密封胶条。胶条原料选用EPDM或氯丁橡胶,肯定制止运用聚氯乙烯(PVC) 的密封胶条。胶条硬度以肖氏65为宜,外表平坦,断面形状共同,无损伤,无变形,不发硬,有弹性。
1 dry assembly method: this method needs to be penetrated into the aluminum material. The use of EPDM or neoprene rubber strip raw materials will definitely stop the use of polyvinyl chloride (PVC) sealant strip. The hardness of the adhesive strip should be Short 65. The surface is flat, the cross-section shape is common, no damage, no deformation, no hardening, elastic.
2湿式装配法:此办法要选用与阳光板原料想习惯的不硬化、低模数、中性或弱酸性密封胶。阳光板与衔接件间密封胶的延伸度要>=50%,要保证阳光板热胀冷缩及风压位移时,胶层不会因拉断发生空隙而形成渗漏。
2. Wet assembling method: This method should choose the sealant which is not hardened, low modulus, neutral or weak acid, which is used to the raw material of sunlight plate. The elongation of the sealant between the solar panel and the connector should be more than 50%. It is necessary to ensure that the sealant layer will not leak due to the breakage of the sealant when the solar panel expands and shrinks and the wind pressure shifts.
3现在改良后的阳光板装置办法分为"专用铝型材装配法"和"扣盖型装配法"。此两种办法需在铝型材或扣盖钢板下压入专用防水胶带。该胶带为进口专用胶带,其标准选型应严厉按工程设计要求。
3 now the improved method of sunshine plate installation is divided into "special aluminum profile assembly method" and "capping assembly method". These two methods need to press special waterproof tape under the aluminum profile or the cover plate. The adhesive tape is imported special adhesive tape, and its standard selection should be strictly according to the engineering design requirements.
4运用自攻螺钉或螺栓衔接铝型材,在紧固时要留意调整好各衔接部位密封性的一起,还要留意不使阳光板、衔接型材及紧固件自身发生形变或损坏,留意装置力度。
4. Use self-tapping screws or bolts to connect aluminum profiles. When fastening, attention should be paid to adjusting the sealing property of each joint part together. Attention should also be paid to preventing deformation or damage of sunshine plate, joint profiles and fasteners. Attention should be paid to the strength of the device.
济南阳光板
5阳光板装置结束,当即揭掉维护膜。如有必要继续维护板面,则应先揭掉,再从头掩盖,以防止阳光长期直射,而发生胶搬运现象,难以揭下。
5 when the sun plate device is finished, the maintenance film will be removed immediately. If it is necessary to continue to maintain the panel, it should be removed first, and then cover from the beginning to prevent long-term direct sunlight, and the occurrence of rubber transport phenomenon, difficult to uncover.
6装置前,施工组织者必定要将维护膜印上的文字阐明和留意事项理解清楚,并向操作人员阐明。特别要留意"含有抗UV保层的面向阳。
Before the installation, the construction organizer must clearly understand the words and precautions on the maintenance diaphragm and explain them to the operator. Special attention should be paid to "facing the sun with anti UV protection layer".
7在装置阳光板时,如需常温曲折板材,请留意阳光板厚度(d)与曲折半径(R)的联系。 多层板 R>=175d 单层板,R>=150d 波纹板,R>=4000mm
7 When installing sunlight panels, if room temperature bending plates are required, please pay attention to the relationship between the thickness (d) of sunlight panels and the bending radius (R). Multilayer R>=175d single board, R>=150d corrugated plate, R>=4000mm
8阳光板厚度及装置标准的断定,与装置区域的根本风庄、根本雪载、装置高度、建筑物体型等许多要素有关。用户在选购阳光板时,要经过科学核算去选购。
The determination of the thickness of the sunlight plate and the installation standard is related to many factors such as the fundamental wind farm, the fundamental snow load, the installation height and the building shape in the installation area. When buying sunshine boards, users should go through scientific calculation and purchase.
(天桥巨龙采光板,对济南阳光板感兴趣的朋友可以关注我们http://www.lushangyun.com,每天提供更多精彩内容)
(Skybridge Dragon Lighting Board, Jinan Sunshine Board interested friends can pay attention to our http://www.lushangyun.com, provide more exciting daily content)
相关新闻


  天桥区欣飞板业经销处            联系人:焦经理            座机:15806664558
 手机:15806664558        15066129603       13969012996
  技术支持: 济南诺商   鲁ICP备14016125号 网站地图 XML TXT

统一服务热线

15806664558 

鲁公网安备 37010502001033号

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】