欢迎访问欢迎访问天桥区欣飞板业经销处!
阳光板、耐力板、FRP(波浪瓦)、灯箱片
我们只生产质量保障的阳光板等产品

统一服务热线:

15806664558

首页>新闻中心>PC耐力板的安装螺丝的使用
产品分类 PRODUCTS
联系我们

天桥区欣飞板业经销处

联系人:焦经理 

电话:15806664558 

手机:15806664558
          15066129603
          13969012996
地址:济南市历城区历山北路佳园装饰材料南区A7-30号


PC耐力板的安装螺丝的使用

来源:http://www.wanzhongyue.com/ 日期:2021-06-29 发布人:julong 浏览次数:

运用耐力板的时候,不仅对板材的质量有极为严格的要求,即便是一颗安装用的螺丝,也必须符合条件,否则就有可能会影响耐力板。
When using the endurance board, not only the quality of the board has extremely strict requirements, even a screw for installation must meet the conditions, otherwise it may affect the endurance board.
首先要记住,在安装耐力板的时候,螺丝孔的位置不要距离耐力板的边缘太近,这样会容易使得板材出现破损的现象。同时还要控制的紧度,防止板材变形和应力的出现。在实际操作的时候,尽量不
First of all, remember that when installing the endurance plate, the position of the screw hole should not be too close to the edge of the endurance plate, which will easily cause the plate to be damaged. At the same time, the tightness of the plate should be controlled to prevent the deformation and stress of the plate. In the actual operation, try not to
要在耐力板上使用自攻螺丝,否则很容易产生不断增大的应力。只要以这些为原则来安装,耐力板一定可以达的安装效果,并在后期的使用中发挥价值。
To use self tapping screws on the endurance plate, otherwise it is easy to produce increasing stress. As long as these principles are used for installation, the endurance board can achieve the same installation effect and play a value in later use.
考虑到不同场合中选用的耐力板的板厚是不一样的,因此在螺丝间距的设置上也好做合理的调整,间距太小或太大对耐力板本身和其利的。另外,还要考虑螺丝孔的尺寸,因为板材不同季节、不同气
Considering that the thickness of the endurance plate is different in different occasions, it's better to make reasonable adjustment in the setting of screw spacing. Too small or too large spacing is beneficial to the endurance plate itself and its benefits. In addition, also consider the size of the screw hole, because the plate is different seasons, different gas
温下热量冷缩的不同。
The heat shrinks differently at different temperatures.
总结以往的经验来看,一般情况下,只要将螺丝孔保持在比螺丝大2-4mm的范围中,以留出一些空间就能符合要求。由于耐力板安能和使用寿命是息息相关的,因此在操作的时候必须格外谨慎,防止对耐力板产品造成损坏。
Summing up the past experience, in general, as long as the screw hole is kept in the range of 2-4mm larger than the screw to leave some space, it can meet the requirements. Because the endurance board safety is closely related to the service life, we must be very careful in the operation to prevent damage to the endurance board products.
以上就是小编今天整理的PC耐力板的安装螺丝的使用知识,希望对大家能够有所帮助,欢迎来电咨询,我们期待您的来电.
The above is the use of the installation screw of the PC endurance board arranged by Xiaobian today. I hope it can help you. Welcome to inquire. We are looking forward to your call
相关新闻


  天桥区欣飞板业经销处            联系人:焦经理            座机:15806664558
 手机:15806664558        15066129603       13969012996
  技术支持:网站建设·推广运营 网站地图 XML TXT

统一服务热线

15806664558 

鲁公网安备 37010502001033号

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】