欢迎访问欢迎访问天桥区欣飞板业经销处!
阳光板、耐力板、FRP(波浪瓦)、灯箱片
我们只生产质量保障的阳光板等产品

统一服务热线:

15806664558

首页>新闻中心>使用阳光板搭建温室大棚需要怎么做?
产品分类 PRODUCTS
联系我们

天桥区欣飞板业经销处

联系人:焦经理 

电话:15806664558 

手机:15806664558
          15066129603
          13969012996
地址:济南市历城区历山北路佳园装饰材料南区A7-30号


使用阳光板搭建温室大棚需要怎么做?

来源:http://www.wanzhongyue.com/ 日期:2021-09-23 发布人:julong 浏览次数:

先检查骨架,必须平整,不得有焊疤,毛刺。骨架上必须彻底干燥,不得有挥发性溶剂。将丁基防水胶带铺设在骨架两边,形成一个小型水槽。将阳光板放置在骨架上,板与板之间预留伸缩缝。将EPDM压条压在板与板之间接口处。用自钻螺丝固定。阳光板宽度中间1.05M处下一定要骨架,是用自钻螺丝套包钮固定。靠墙面阳光板不得与墙面直接接触,用角铝固定在墙面,再将阳光板套进去,装上去。阳光板收口处先用铝泊胶带将口封好,再将收边条或角铝固定好。
Check the framework first. It must be flat and free of welding scar and burr. The skeleton must be completely dry without volatile solvents. Lay butyl waterproof tape on both sides of the skeleton to form a small water tank. Place the sunlight board on the skeleton, and reserve expansion joints between the boards. Press the EPDM strip at the interface between the plates. Secure with self drilling screws. The frame must be set at 1.05M in the middle of the width of the sunlight plate, which is fixed with self drilling screw sleeve button. The sunlight board against the wall shall not be in direct contact with the wall. It shall be fixed on the wall with angular aluminum, and then the sunlight board shall be sleeved in and installed. At the closing of the sunlight plate, seal the opening with aluminum parking tape, and then fix the closing strip or corner aluminum.
其次在安装中空板和实心耐力板时,在板与板接缝处,必须根据板材尺寸预留热膨胀间隙,热膨胀系数为0.065mm/m℃,严禁自攻钉,拉铆钉等直接穿过板材固定。若一定要穿过时,必须在板材上钻孔直径大于自攻钉或拉铆钉的直径100%的扩大孔,再降自攻钉或铆钉通过扩大孔的圆心,以确保板材能够在任意方向自由伸缩。
Secondly, when installing hollow plate and solid endurance plate, thermal expansion gap must be reserved at the joint between plate and plate according to the plate size, and the thermal expansion coefficient is 0.065mm/m ℃. It is strictly prohibited to fix self tapping screws and pull rivets directly through the plate. If it is necessary to pass through, an enlarged hole with a diameter greater than 100% of the diameter of the self tapping screw or pull rivet must be drilled on the plate, and then the center of the circle of the self tapping screw or rivet passing through the enlarged hole must be lowered to ensure that the plate can expand and contract freely in any direction.
济南阳光板
与阳光板温室接触的密封胶必须选用中性硅铜胶,严禁使用碱性,酸性,化学成分不明的含有溶剂的密封胶。避免阳光板与化学溶剂,溶液和挥发性气体直接接触,若采用稀料稀释的油漆喷刷阳光板支撑架时,必须带油漆完全干燥后方可安装阳光板,严禁用稀料稀释的油漆补刷已安装阳光板的钢骨架。
Finally, neutral silicon copper sealant must be selected for the sealant in contact with the sunlight plate greenhouse. It is strictly prohibited to use the sealant containing solvent with alkaline, acidic and unknown chemical composition. Avoid direct contact between the sunlight plate and chemical solvents, solutions and volatile gases. If the sunlight plate support frame is sprayed with thinner diluted paint, the sunlight plate must be installed after the paint is completely dry. It is strictly prohibited to use thinner diluted paint to repair the steel framework of the installed sunlight plate.
搭建阳光板温室大棚首先要有钢构支撑,可用方管或圆管做钢构,也可用不锈钢做钢构,一般来说阳光板大棚都是做成弧形,这样有利于顶部的排水,提醒大家中间间距不要太宽,否则安装后会导致板面下垂。
To build a solar panel greenhouse, it is first necessary to have a steel structure support. Square tubes or round tubes can be used as steel structures, and stainless steel can also be used as steel structures. Generally speaking, the solar panel greenhouse is made into an arc, which is conducive to the drainage at the top and reminds everyone that the middle spacing should not be too wide, otherwise the plate surface will sag after installation.
相关新闻


  天桥区欣飞板业经销处            联系人:焦经理            座机:15806664558
 手机:15806664558        15066129603       13969012996
  技术支持:网站建设·推广运营 网站地图 XML TXT

统一服务热线

15806664558 

鲁公网安备 37010502001033号

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】