欢迎访问欢迎访问天桥区欣飞板业经销处!
阳光板、耐力板、FRP(波浪瓦)、灯箱片
我们只生产质量保障的阳光板等产品

统一服务热线:

15806664558

首页>新闻中心>阳光板拼接处密封怎么处理?
产品分类 PRODUCTS
联系我们

天桥区欣飞板业经销处

联系人:焦经理 

电话:15806664558 

手机:15806664558
          15066129603
          13969012996
地址:济南市历城区历山北路佳园装饰材料南区A7-30号


阳光板拼接处密封怎么处理?

来源:http://www.wanzhongyue.com/ 日期:2021-11-26 发布人:julong 浏览次数:

阳光板在安装的时候,会涉及到拼接处处理,一定要做好细节,做好密封,处理不当,在雨天、雪天、刮风的时候都会有影响。那么具体该怎么做好?正确的安装方法以及合适的材料,接下来河南东信板业有限公司分享阳光板拼接处具体密封处理方法。
When installing the sunlight board, it will involve the splicing treatment. We must do a good job in details and sealing. Improper treatment will have an impact in rainy, snowy and windy days. So how to do it? The correct installation method and appropriate materials. Next, Henan Dongxin board Co., Ltd. shares the specific sealing treatment method of sunshine board splicing.
安装阳光板时,无论何种情况,都应将阳光板与加强筋垂直安装。这样安装阳光板是为了加强板的强度,防止雪压、强风等。我们知道,固定阳光板的常用方法是使用压条。水珠阻塞了雨水的排放,同时也促了藻类的生长(板子在凹凸的水珠中会有沉积物),这是由于冷凝水在一定温度下长期堆积在凹槽内造成的。
When installing the sunlight plate, in any case, the sunlight plate shall be installed vertically with the stiffener. In this way, the sunlight board is installed to strengthen the strength of the board and prevent snow pressure, strong wind, etc. As we know, the common way to fix the sun board is to use battens. Water droplets block the drainage of rainwater and promote the growth of algae (there will be sediment in the concave convex water droplets on the board), which is caused by the long-term accumulation of condensate in the groove at a certain temperature.
由于凹槽中的水分积聚和灰尘/昆虫污染可能是一个主要问题,因此安装过程中更重要的方面之一是边缘密封,特别是对于带有开口端的凹槽。有一些方法可以大大减少污染,具体选择哪种方法在很大程度上取决于当地的环境条件。
Since moisture accumulation and dust / insect contamination in grooves may be a major problem, one of the more important aspects of the installation process is edge sealing, especially for grooves with open ends. There are some methods that can greatly reduce pollution, and the specific choice of which method depends largely on local environmental conditions.
阳光板的边缘用胶带覆盖。这是阳光板自带的胶带,仅用于在运输和储存过程中保护板。它们不是不可透的密封和安装胶带。安装前,这些胶带应更换为下述胶带。
The edges of the solar panel are covered with tape. This is the tape that comes with the solar panel and is only used to protect the panel during transportation and storage. They are not impermeable sealing and installation tapes. Before installation, these tapes should be replaced with the following tapes.
使用胶带前,应将板的所有边缘去除约50mm的遮蔽膜。剩余的遮蔽膜只能在安装后去除。
Before using the tape, the masking film of about 50mm shall be removed from all edges of the plate. The remaining masking film can only be removed after installation.
胶带应具有良好的耐候性,长期使用后粘度和机械强度不会下降。
The tape shall have good weather resistance, and the viscosity and mechanical strength will not decrease after long-term use.
胶带应具有良好的抗撕裂性和良好的抗安装和搬运过程中的其他损坏能力。
The tape shall have good tear resistance and good resistance to other damage during installation and handling.
我们要知道,过去的密封条件是安装胶条后使用密封胶来解决密封问题,但是从以往的经验来看,阳光板会随着天气的变化而膨胀收缩,导致板子移动,所以固定PC板上的密封胶也会随着板子移动,久而久之会造成很多缝隙,所以我们建议您在安装珠子之前在板子的缝隙之间粘上防水胶带。
We should know that in the past, the sealing condition was to use sealant to solve the sealing problem after installing the rubber strip. However, from past experience, the sunshine board will expand and contract with the change of weather, resulting in the movement of the board. Therefore, the sealant on the fixed PC board will also move with the board, which will cause many cracks over time, Therefore, we recommend that you stick waterproof tape between the gaps of the board before installing the beads.
所有孔隙均应填充中性密封胶,外露部位应涂中性密封胶,防止清洗剂渗入边缘,防止延长开裂;当发现安装缺陷时,可将其添加到可能发生泄漏的部位。密封剂组成。密封胶应该是一种中性耐候硅橡胶,在固化后仍保持柔软、低模量的伸长率。铝型材和板材表面在涂胶前清洁干燥,不得有油污和灰尘、水汽、露珠等杂物,施胶均匀,胶层表面光滑,断面尺寸一致,不得有间断;需要特别注意的是,所使用的中性密封胶预先测试与板的兼容性。避免与阳光板或耐力板发生化学反应。
All pores shall be filled with neutral sealant, and the exposed parts shall be coated with neutral sealant to prevent cleaning agent from penetrating into the edge and prolonged cracking; When installation defects are found, they can be added to the parts where leakage may occur. Sealant composition. The sealant shall be a kind of neutral weather resistant silicone rubber, which remains soft and low modulus elongation after curing. The surface of aluminum profile and plate shall be clean and dry before gluing, free of oil, dust, water vapor, dew and other sundries, uniform gluing, smooth surface of adhesive layer, consistent section size and no interruption; Special attention should be paid to the compatibility of the neutral sealant used with the plate in advance. Avoid chemical reaction with sunlight board or endurance board.
以上就是济南阳光板提供的精彩内容,更多消息请关注http://www.wanzhongyue.com
The above is the wonderful content provided by Jinan sunshine board. Please pay attention to more information http://www.wanzhongyue.com
相关新闻


  天桥区欣飞板业经销处            联系人:焦经理            座机:15806664558
 手机:15806664558        15066129603       13969012996
  技术支持:网站建设·推广运营 网站地图 XML TXT 备案:鲁ICP备14016125号-1

统一服务热线

15806664558 

鲁公网安备 37010502001033号

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】