欢迎访问欢迎访问天桥区欣飞板业经销处!
阳光板、耐力板、FRP(波浪瓦)、灯箱片
我们只生产质量保障的阳光板等产品

统一服务热线:

15806664558

首页>新闻中心>济南阳光板的安装方法以及注意事项
产品分类 PRODUCTS
联系我们

天桥区欣飞板业经销处

联系人:焦经理 

电话:15806664558 

手机:15806664558
          15066129603
          13969012996
地址:济南市历城区历山北路佳园装饰材料南区A7-30号


济南阳光板的安装方法以及注意事项

来源:http://www.wanzhongyue.com/ 日期:2021-12-23 发布人:julong 浏览次数:

阳光板得益于它良好的透光性、耐冲击性、耐用性等多项杰出性能,PC阳光板在建筑、户外、农业等多个领域铺开。好的PC阳光板品牌与产品早已闻名遐迩,选择好的产品不再是难题,但是不得不承认的就是,目前许多客户和安装方对PC阳光板的相关知识仍然不太了解,安装和使用过程中可能会出现因方法不对而导致的板材损坏。因此,燚塑科技在这里也为大家准备了一份安装使用攻略,以供大家安装过程中参考。
Thanks to its good light transmittance, impact resistance, durability and other outstanding properties, PC sunshine board has been spread in many fields such as construction, outdoor, agriculture and so on. Good PC sunshine board brands and products have long been famous, and choosing good products is no longer a problem, but it must be admitted that many customers and installers still don't know much about PC sunshine board, and the board may be damaged due to incorrect methods during installation and use. Therefore, plastic technology has also prepared an installation strategy for you here for your reference in the installation process.
安装注意事项;一般来说,PC阳光板产品都会在保护膜上印有文字说明和注意事项,安装者需要仔细阅读,避免出现错误。在这其中,特别要注意的是向阳面的问题,要知道,PC阳光板多数为单面紫外线防护层,如果装反的话,PC阳光板将不能抵御紫外线的侵袭,容易出现老化、黄化、脆化的问题,影响严重。
Installation precautions; Generally speaking, PC sunshine board products will be printed with text instructions and precautions on the protective film. Installers need to read them carefully to avoid errors. Among them, special attention should be paid to the problem of the sunny side. You should know that most PC sunshine boards are single-sided UV protective layers. If they are installed reversely, PC sunshine boards will not be able to resist the invasion of UV, and are prone to aging, yellowing and embrittlement, which will have a serious impact.
在安装过程中,我们首先将板材运至安装位置,撕去一片板材底部保护膜,用盖帽定位,再揭除二片板材底部保护膜,用盖帽定位后,在二片板材相接处贴上防水胶带,将压条压在防水胶带的正上方。
In the installation process, we first transport the plate to the installation position, tear off the protective film at the bottom of one plate, position it with a cap, then remove the protective film at the bottom of the two plates, position it with a cap, paste waterproof tape at the joint of the two plates, and press the pressure strip directly above the waterproof tape.
螺丝安装法;如果使用螺丝安装法的话,螺丝间距,可依板厚,作适当的配置,间距太小及太大均不好。如间距太小,有时会因太紧而引发应力,造成破坏;如间距太大,又可使PC板固定不稳。为此推荐采用下间距注:如用自攻螺丝直接固定PC板,则螺丝间距越大,板材越不易因应力而损坏。
Screw installation method; If the screw installation method is used, the screw spacing can be properly configured according to the plate thickness. Too small or too large spacing is not good. If the spacing is too small, sometimes it will cause stress and damage due to too tight; If the spacing is too large, the PC board can be fixed unstable. For this reason, the following spacing is recommended. Note: if the PC board is directly fixed with self tapping screws, the greater the screw spacing, the less likely the plate is to be damaged due to stress.
另外,在连接型材中或在镶框的镶槽中一定要留出空间以便板材受膨胀和受载位移。PC阳光板的线性热膨胀系数是0.065mm/m℃,即温度每升高1℃,1m×1m板顺着长度方向各膨胀0.065mm,用户须根据工程所在地四季温差,算出安装间隙的数据:如北方地区,温度高达40℃,温度低至-30℃,1m×1m的板材安装预留间隙为0.065×70=4.55mm。
In addition, space must be reserved in the connecting profile or in the slot of the frame so that the plate can expand and move under load. The linear thermal expansion coefficient of PC sunlight plate is 0.065mm/m ℃, i.e. 1m for every 1 ℃ increase in temperature × The 1m plate expands by 0.065mm along the length direction. The user must calculate the data of installation clearance according to the temperature difference in four seasons of the project location: for example, in northern areas, the temperature is as high as 40 ℃ and as low as - 30 ℃, 1m × The reserved gap for 1m plate installation is 0.065 × 70=4.55mm。
湿式装配法;湿式装配法主要用于小型的设施,如车棚、雨棚、温室以及其它许多替代玻璃的场合。当采用这种方法的时候,基本要求是密封系统要能承受板材一定量的移动,允许热膨胀而不降低其与框架及板材之间的粘结力。
Wet assembly method; Wet assembly method is mainly used in small facilities, such as car shed, canopy, greenhouse and many other occasions instead of glass. When this method is adopted, the basic requirement is that the sealing system should be able to bear a certain amount of movement of the plate and allow thermal expansion without reducing the bonding force between the sealing system and the frame and the plate.
一般推荐使用中性硅酮胶和三元乙丙胶水等进行与中空阳光板的湿式装配。但要特别注意的是,在使用前一定要检查所用密封胶的化学性,不可选用酸性及碱性硅酮胶,因为这些固化剂会导致板材龟裂,尤其当有内应力时,在选用密封胶时,除考虑化学适性外,还要检验延伸度及耐候性等。
It is generally recommended to use neutral silicone glue and EPDM glue for wet assembly with hollow sunshine board. However, it should be noted that the chemical properties of the sealant used must be checked before use. Acidic and alkaline silicone adhesives cannot be selected, because these curing agents will lead to plate cracking. Especially when there is internal stress, when selecting sealant, in addition to chemical suitability, elongation and weather resistance shall be checked.
密封注意事项;PC阳光板上原有的胶带仅为临时保护板材边缘所用,是不耐老化的,在安装工程中,按尺寸裁板,下料后一定要用工程专用胶带按安装规程的要求密封板端孔格,把原来胶带替换下来。安装工程专用胶带应有很好的耐候性,长期使用而不丧失其粘结性和机械强度。
Sealing precautions; The original tape on PC sunshine board is only used to temporarily protect the edge of the board and is not resistant to aging. In the installation project, the Board shall be cut according to the size. After blanking, the special engineering tape must be used to seal the plate end hole grid according to the requirements of the installation regulations and replace the original tape. The special adhesive tape for installation engineering shall have good weather resistance and shall not lose its adhesion and mechanical strength after long-term use.
安装工程专用胶带时,要注意以下几点:(1)保证板材边缘都是光滑的。(2)要将所有孔吹干净,压缩空气一定要是无任何杂质,干燥的。(3)要保证用型材、金属盖板,端部的U形保护槽把胶带完全盖住,安装完成后,不应该有暴露的部分。
When installing the special adhesive tape for the project, pay attention to the following points: (1) ensure that the edge of the plate is smooth. (2) blow all holes, and the compressed air must be free of any impurities and dry. (3) ensure that the adhesive tape is completely covered with profile, metal cover plate and U-shaped protective groove at the end. After installation, there should be no exposed part.
清洁方法;因为PC阳光板具有不耐酸碱和不耐刮花的缺点,清洁需要更加注意。使用过程中要清洗的话,一定要使用60℃以下的温水冲洗,并使用中性的洗涤剂,切忌使用对PC阳光板有侵蚀作用的酸碱洗涤剂,其次,要求用软布或海绵蘸中性液轻轻擦洗。禁用粗布、刷子、拖把等其它坚硬、锐利工具实施清洗。
Cleaning methods; Because PC sunshine board has the disadvantages of acid and alkali resistance and scratch resistance, cleaning needs more attention. If you want to clean it during use, you must use warm water below 60 ℃ and neutral detergent. Do not use acid-base detergent that has corrosive effect on PC sunshine board. Secondly, it is required to gently scrub it with soft cloth or sponge dipped in neutral liquid. It is forbidden to clean with coarse cloth, brush, mop and other hard and sharp tools.
本文由济南阳光板为您提供,我们的网站是:http://www.wanzhongyue.com我们将以全心全意的热情为您提供服务,欢迎您的访问!
This article is provided by Jinan sunshine board. Our website is: http://www.wanzhongyue.com We will serve you with wholehearted enthusiasm. Welcome to visit!
相关新闻


  天桥区欣飞板业经销处            联系人:焦经理            座机:15806664558
 手机:15806664558        15066129603       13969012996
  技术支持:网站建设·推广运营 网站地图 XML TXT 备案:鲁ICP备14016125号-1

统一服务热线

15806664558 

鲁公网安备 37010502001033号

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】