欢迎访问欢迎访问天桥区欣飞板业经销处!
阳光板、耐力板、FRP(波浪瓦)、灯箱片
我们只生产质量保障的阳光板等产品

统一服务热线:

15806664558

首页>新闻中心>pc阳光板装置留意事项
产品分类 PRODUCTS
联系我们

天桥区欣飞板业经销处

联系人:焦经理 

电话:15806664558 

手机:15806664558
          15066129603
          13969012996
地址:济南市历城区历山北路佳园装饰材料南区A7-30号


pc阳光板装置留意事项

来源:http://www.wanzhongyue.com/ 日期:2018-11-07 发布人:admin 浏览次数:

pc阳光板装置留意事项
PC solar panel device matters needing attention
pc阳光板易于装置加工,冷弯热弯皆可。pc阳光板装置前请仔细阅读以下阐明。
PC sun panel is easy to machine, cold bending and hot bending. Please read the following instructions carefully before the PC solar panel installation.
1.装置前有必要保证骨架的平坦和清洁;
1. it is necessary to ensure that the skeleton is flat and clean before installation.
2.先查看板材的裁切尺度和胀大预留量是否合格,要特别留意留出足够的均匀的胀大空隙,计算公式如下:
2. First, check whether the cutting scale and expansion reserve are qualified, and pay special attention to leaving enough uniform expansion voids. The calculation formula is as follows:
总胀大空隙=胀大系数×当地装置前后较大的温差×板材长度
Total swell gap = swell coefficient * maximum temperature difference before and after the local device * plate length
线性热胀大系数为7.0×10-5mm/mm.K,即温度每升高1度,1m×1m的板材顺着长宽方向各胀大7.0×10-5mm(0.07mm)
The linear thermal expansion coefficient is 7.0 *10-5mm/mm.K, i.e. for each temperature rise of 1 degree, 1 m *1m plate expands 7.0 *10-5mm (0.07 mm) along the direction of length and width.
3.板材热胀冷缩系数与支撑结构不同,且需要留余量以接受风压.雪压等,因而嵌入量要预留充沛,以及热胀冷缩的空间。一般板材边际伸入固定结构25mm以上,并至少有二条楞筋装置时固定区域;热胀冷缩一般每米留3mm空隙。
3. The coefficient of thermal expansion and contraction of sheet metal is different from that of support structure, and it needs to leave a margin to accept wind pressure, snow pressure and so on. Therefore, sufficient space for thermal expansion and contraction of sheet metal should be reserved. Generally, the edge of the plate extends into the fixed structure more than 25 mm, and there are at least two ribs in the fixed area; thermal expansion and cold contraction generally leave 3 mm void per meter.
4.认明板材表面防紫外线的一面,并把该面朝外装置,绝不允许把防紫外线的一面朝内装置。
4. Identify the anti-ultraviolet side of the surface of the sheet, and put the facing device outward. Never allow the anti-ultraviolet side facing inward device.
5.在装置板材时,板材上所覆维护膜会影响填缝料与板材的结合,所以在装置前把板材四周的维护膜揭起5~10cm,不要让型材夹住维护膜,但也不可揭起太多,避免因操作而损伤板面。
5. When installing sheet metal, the overlying maintenance film on the sheet metal will affect the combination of filling material and sheet metal. Therefore, before installing, lift the maintenance film around the sheet metal for 5-10 cm. Do not let the profile clamp the maintenance film, but also do not lift too much, so as to avoid damaging the surface of the sheet due to operation.
留意:有些工人操作时把维护膜夹在型材里,然后用尖利东西划印再揭起,但往往划伤板面而导致板材损坏。
Note: Some workers clip the maintenance film in the profile when they operate, and then use sharp things to mark and uncover, but often scratch the surface of the plate and cause damage to the plate.
6.板材冷弯装置的情况下,耐力板其曲折半径不得小于板材厚度的100倍,阳光板其曲折半径不得小于板材厚度的175倍;阳光板只能顺楞筋方向曲折。
6. In the case of plate cold bending device, the bending radius of the endurance plate shall not be less than 100 times the thickness of the plate, and the bending radius of the sunshine plate shall not be less than 175 times the thickness of the plate; the sunshine plate shall only bend along the direction of the corrugated ribs.
7.如须在板上直接固定自攻自钻钉,须扩孔,一切钻孔直径应大于螺栓直径,留出热胀冷缩空隙;故在材板开孔时,孔径须比螺丝直径大50%,在曲折部分避免锁螺丝,避免形成裂板。
7. If the self-tapping self-drilling screw is to be fixed directly on the board, it is necessary to enlarge the holes. The diameter of all holes should be larger than the diameter of the bolt, leaving thermal expansion and cold contraction voids. Therefore, when opening the holes in the board, the hole diameter should be 50% larger than the diameter of the screw, so as to avoid locking the screw in the zigzag part and forming the crack plate.
济南阳光板
8.自攻螺丝拧紧时用力要均匀,保证型材真正压实密封胶条和板材,一起亦要避免螺丝锁紧过度,致使阳光板变形。
8. When self-tapping screw is tightened, the force should be uniform to ensure that the profile really compacts the sealant strip and plate. Together, the excessive locking of the screw should be avoided, resulting in the distortion of the sunshine plate.
9.一切孔隙应以中性密封胶填充,并以中性密封胶涂敷显露部分以避免清洁剂进入边际,避免延发性龟裂;当发现装置缺点时,在可能发作渗漏的部位可加以密封胶进行补偿。选用密封胶要选用固化后仍保持柔软.低模数.延伸率大于50%的中性耐候硅酮胶,施胶前必定要使铝型材及板材的表面清洁和枯燥,做到无油污.尘土.水汽.露珠及其它杂物,施胶要均匀,胶层表面润滑,断面尺度一致并不得有连续现象;须特别留意的是所运用的中性密封胶有必要提早与板材做相容性试验,以避免与板材发作化学反应。
9. All pore should be filled with neutral sealant, and the exposed part should be coated with neutral sealant to avoid detergent entering the margin and delayed cracking. Sealant can be used to compensate for leakage when defects of the device are found. Sealants should be used to keep soft, low modulus, neutral weather-resistant silicone gel with elongation greater than 50%. Before sizing, the surface of aluminium profiles and sheets must be clean and dry, so that there is no oil pollution, dust, water vapor, dew and other impurities. The sizing should be uniform, the surface of the adhesive layer should be lubricated, and the cross-section size should not be uniform. Continuous phenomena; special attention should be paid to the need for early compatibility test of the neutral sealant used with the sheet in order to avoid chemical reactions with the sheet.
10.孔的中心到板材边际距离应大于等于2.5cm。
The distance from the center of the 10. hole to the plate should be greater than or equal to 2.5cm.
11.板材在平面式装置时,主张顺楞筋方向细微歪斜,歪斜的斜度至少5°(每米长,头端高10cm),以利于排水,若归于多雪区域要求歪斜更多以避免积雪过厚。
11. In planar installations, it is advocated that the slab should be slightly skewed along the direction of the corrugated ribs, and that the skewness should be at least 5 degrees (10 cm high at the end of each meter) in order to facilitate drainage. If it belongs to the snowy area, more skewness should be required to avoid excessive snow cover.
12.板材装置全过程中严禁足踏板面,操作时须运用跨越板材的可移式踏板。
12. during the whole process of plank installation, no foot pedal is strictly prohibited, and the movable pedal that crosses the plate must be used during operation.
13.PC板裁切长度务必大于宽度才可曲折。
The cutting length of the 13.PC board must be larger than the width.
14.板材装置好后要求当即揭掉维护膜,如因施工特殊要求维护板面,也须先揭掉维护膜,然后从头覆盖。
14. When the plate is installed, the maintenance film should be removed immediately. If the plate surface is maintained due to special construction requirements, the maintenance film should be removed first, and then covered from scratch.
15.板材装置好后应进行自检,特别要仔细做喷淋试验,查看是否漏水,如有漏水隐患应及时消除,然后再查看外观质量。
15. After the plate is installed, it should be self-checked. Especially, spray test should be done carefully to check whether there is leakage. If there is potential leakage, it should be eliminated in time, and then the appearance quality should be checked.
更多关于济南阳光板问题或者详细内容,请关注天桥巨龙采光板的网站:http://www.wanzhongyue.com网站中会有很多的内容仅供参考。
For more information about Jinan Sunshine Plate, please pay attention to the website of the Bridge Dragon Sunshine Plate: http://www.wanzhongyue.com, there will be a lot of content for reference only.
相关新闻


  天桥区欣飞板业经销处            联系人:焦经理            座机:15806664558
 手机:15806664558        15066129603       13969012996
  技术支持: 济南诺商   鲁ICP备14016125号 网站地图 XML TXT

统一服务热线

15806664558 

鲁公网安备 37010502001033号

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】