欢迎访问欢迎访问天桥区欣飞板业经销处!
阳光板、耐力板、FRP(波浪瓦)、灯箱片
我们只生产质量保障的阳光板等产品

统一服务热线:

15806664558

首页>新闻中心>阳光板装置留意事项
产品分类 PRODUCTS
联系我们

天桥区欣飞板业经销处

联系人:焦经理 

电话:15806664558 

手机:15806664558
          15066129603
          13969012996
地址:济南市历城区历山北路佳园装饰材料南区A7-30号


阳光板装置留意事项

来源:http://www.wanzhongyue.com/ 日期:2019-01-23 发布人:admin 浏览次数:

阳光板装置留意事项
Cautions for Solar Plate Installation
1.先反省板材的裁切尺寸和膨涨预留量能否适宜,要特别留意留出足够的平均的膨涨间隙,计算公式如下:总膨涨间隙=膨涨系数*外地安裃前后较大的温度*板材长度。
1. Reflect on the appropriateness of the cutting size and expansion reserve, and pay special attention to reserving enough average expansion gap. The calculation formula is as follows: the total expansion gap = expansion coefficient * maximum temperature * plate length before and after the field crotch.
2.中空板装置工程中板材被型板夹持的局部必需至多含有一条筋肋,戒者板材边缘被夹持的局部较小20MM。
2. In the hollow plate installation project, the part where the plate is clamped by the profiled plate must contain at most one rib, and the part where the edge of the disciple plate is clamped is at least 20MM.
3.认明板材外表防紫外线的一面,并把该面朝外安裃,绝不允许把防紫外线的一面朝内装置。
3. Identify the anti-ultraviolet side of the exterior of the sheet and place it on the outer side of the crotch. Never allow the anti-ultraviolet side to face inward.
4.装置前把板材周围的维护膜揭起30MM-50MM,不要让型材夹住维护膜,但也不可揭去太多,以免因操作而损坏板面。
4. Before installation, lift the maintenance film around the sheet metal from 30MM to 50MM. Do not let the profile clamp the maintenance film, but do not uncover too much, so as not to damage the sheet surface due to operation.
5.自攻钉拧紧时用力要平均,确保型板真正压实密封胶条和板材。
5. When self-tapping nails are tightened, the force should be averaged to ensure that the profiles really compact sealant strips and plates.
6.中空板材冷弯装置的状况下,其弯曲半径不得小于析材厚度的175倍。
6. Under the condition of cold bending device for hollow sheet, the bending radius should not be less than 175 times of the thickness of the sheet.
济南阳光板
7.中空板材只能顺肋筋方向弯曲。
7. Hollow plate can only bend along rib direction.
8.中空板材倾斜装置应顺肋筋方向,有利于冷凝水导出。
8. The inclination device of hollow plate should be along the rib direction, which is beneficial to condensate water export.
9.阳光板板材装置好后要求立刻揭掉维护膜,如因施工特殊要求维护板面,也须先揭掉维护膜,然后重新掩盖。
9. After the installation of the sunshine plate, it is required to remove the maintenance film immediately. If the surface is maintained due to the special requirements of construction, the maintenance film must be removed first and then re-covered.
10.板材装置好后应停止自检,特别要仔细做喷淋实验,反省能否漏水,如有漏水隐患应及时消弭,然后再反省外观质量。
10. After the plate is installed, the self-inspection should be stopped, especially the spraying experiment should be done carefully, and the leak should be checked. If there is a potential leak, the leak should be eliminated in time, and then the appearance quality should be checked.
11.板材装置全进程中严禁足踏板面,操作时须运用跨越板材的可挪动式踏板。
11. It is strictly forbidden to foot the pedal in the whole process of the plate device. Movable pedals across the plate should be used in operation.
12.如须在板上间接固定自攻自钻钉时,须扩孔,一切钻孔直径应大于螺栓直径,留出热胀冷缩间隙
12. If self-tapping self-drilling nails are to be indirectly fixed on the board, the hole should be enlarged. The diameter of all boreholes should be larger than the diameter of bolts, leaving a gap between thermal expansion and cold contraction.
13.孔的中心到板材边缘间距应大于等于5CM。
13. The distance between the center of the hole and the edge of the plate should be greater than or equal to 5CM.
综上所述有天桥巨龙采光板提供,想了氧更多济南阳光板知识,欢迎关注我们的网站:http://www.wanzhongyue.com谢谢支持!
In summary, the above-mentioned Tianqiao Julong lighting board provides more knowledge of Jinan sunshine board. Welcome to our website: http://www.wanzhongyue.com. Thank you for your support!
相关新闻


  天桥区欣飞板业经销处            联系人:焦经理            座机:15806664558
 手机:15806664558        15066129603       13969012996
  技术支持: 济南诺商   鲁ICP备14016125号 网站地图 XML TXT

统一服务热线

15806664558 

鲁公网安备 37010502001033号

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】