欢迎访问欢迎访问天桥区欣飞板业经销处!
阳光板、耐力板、FRP(波浪瓦)、灯箱片
我们只生产质量保障的阳光板等产品

统一服务热线:

15806664558

首页>新闻中心>阳光板怎么固定
产品分类 PRODUCTS
联系我们

天桥区欣飞板业经销处

联系人:焦经理 

电话:15806664558 

手机:15806664558
          15066129603
          13969012996
地址:济南市历城区历山北路佳园装饰材料南区A7-30号


阳光板怎么固定

来源:http://www.wanzhongyue.com/ 日期:2019-03-26 发布人:admin 浏览次数:

  阳光板安装方法:
  Installation method of sunplate:
  一,阳光板弯曲时应顺着力的方向,切不可横向弯曲。弯曲半径为板材厚度:中空二层板175倍 一下,三层板185倍以下,四层板200倍一下。实心耐力板弯曲半径同样为厚度的175倍以下。板材弯曲部位严禁用螺丝固定。
  First, when bending the sunshine plate, it should follow the direction of force, and must not bend horizontally. The bending radius is the thickness of the plate: 175 times of the hollow two-layer plate, 185 times of the three-layer plate and 200 times of the four-layer plate. The bending radius of solid endurance plate is also less than 175 times the thickness. No screw is allowed to fix the bending part of the plate.
  二,在安装中空板和实心耐力板时,在板与板接缝处,必须根据板材尺寸预留热膨胀间隙,热膨胀系数为0.065mm/m℃,严禁自攻钉,拉铆钉等直接穿过板材固定。若一定要穿过时,必须在板材上钻孔直径大于自攻钉或拉铆钉的直径100%的扩大孔,再降自攻钉或铆钉通过扩大孔的圆心,以确保板材能够在任意方向自由伸缩。
  Secondly, when installing hollow plate and solid endurance plate, the thermal expansion gap must be reserved at the joint of plate and plate according to the size of plate. The coefficient of thermal expansion is 0.065 m m/m C. It is strictly forbidden to tap nails and pull rivets directly through the plate and fix them. If it is necessary to pass through, the enlarged hole with a diameter greater than 100% of the diameter of the self-tapping nail or rivet must be drilled on the plate, and then the self-tapping nail or rivet must be lowered through the center of the enlarged hole to ensure that the plate can expand freely in any direction.
  三,与阳光板接触的密封胶必须选用中性硅铜胶,严禁使用碱性,酸性,化学成分不明的含有溶剂的密封胶。避免阳光板与化学溶剂,溶液和挥发性气体直接接触,若采用稀料稀释的油漆喷刷阳光板支撑架时,必须带油漆完全干燥后方可安装阳光板,严禁用稀料稀释的油漆补刷已安装阳光板的钢骨架。
  Third, the sealant in contact with the sunshine plate must be neutral silica-copper gel. It is strictly prohibited to use alkaline, acidic sealants containing solvents with unknown chemical composition. Avoid direct contact with chemical solvents, solutions and volatile gases. When using diluted paint to spray the sunplate support frame, it must be completely dried with paint before installing the sunplate. It is strictly forbidden to use diluted paint to repair the steel skeleton of the installed sunplate.
  四,阳光板安装固定务必采用本公司专用防漏雨上下成套扣件或本公司提供的专用平板压条,若采用其它公司的平板胶条必须保证胶条的材质为EPDM橡胶或者丁橡胶,严禁采用聚氯乙烯(PVC),天然橡胶等含有对阳光板有害的物质胶条。
  Fourthly, the installation and fixing of the sunshine board must adopt the complete set of fasteners specially designed by our company or the special flat press strip provided by our company. If using the flat rubber strip of other companies, the material of the rubber strip must be EPDM rubber or butadiene rubber. It is strictly prohibited to use the rubber strip containing harmful substances such as polyvinyl chloride (PVC), natural rubber and so on.
  五,安装光板时一定要将板材有UV共挤防紫外线层的带有文字的保护膜一侧朝室外,切不可装反,安装完成后立立即揭除保护膜,避免经太阳暴晒后保护膜和阳光板粘连。
  Fifthly, when installing the light plate, one side of the protective film with text and UV co-extrusion anti-ultraviolet layer of the plate must be facing outdoors. It must not be reversed. The protective film should be removed immediately after installation, so as to avoid adhesion between the protective film and the sunplate after sunshine exposure.
  六,阳光板安装前应揭开距边缘约30mm范围的保护膜,严禁将保护膜压在型材下,再用刀划开保护膜的揭膜方法。阳光板的任何部位均不能有划痕。
  Sixthly, the protective film should be uncovered about 30 mm away from the edge before the installation of the sunshine plate. It is strictly forbidden to press the protective film under the profile and then cut the protective film with a knife. No scratches can be made on any part of the sunplate.
  七,阳光板剖开的断面用铝箔胶带或防水透气胶带封住,以免水蒸汽
  Seventh, the section cut by sunshine plate is sealed with aluminium foil tape or waterproof breathable tape to avoid water vapor.
  阳光板在运输时注意的事项:
  Matters needing attention in transportation of sunshine panels:
  (1)要在室内保存,绝不允许日光直接照射或雨淋
  (1) To keep indoors, no direct sunlight or rain should be allowed.
  (2)用手码放,板上不得压重物,板材之间不得有硬物。
  (2) Place it by hand code. No heavy objects are allowed on the board and no hard objects are allowed between the boards.
  (3)贮藏室须保持洁净、干燥、避免灰尘侵入。室内不应同时存放 其它化学物质。
  (3) Storage rooms should be kept clean, dry and free from dust invasion. Other chemicals should not be stored in the room at the same time.
                                        济南阳光板
  (4)贮存时,不得损坏或揭掉保护膜。
  (4) The protective film shall not be damaged or removed during storage.
  (5)运输时必须平放于面积大于板材的干净平面托盘上,如有需要应适当绑住以避免震动和滑动,注意保护好板边不使受损和双面保护 膜保持完整无缺。
  (5) When transporting, it must be placed on a clean flat pallet with an area larger than the plate. If necessary, it should be properly tied to avoid vibration and sliding. Care should be taken to protect the edge of the plate from damage and to keep the double-sided protective film intact.
相关新闻


  天桥区欣飞板业经销处            联系人:焦经理            座机:15806664558
 手机:15806664558        15066129603       13969012996
  技术支持: 济南诺商   鲁ICP备14016125号 网站地图 XML TXT

统一服务热线

15806664558 

鲁公网安备 37010502001033号

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】